View previous topic :: View next topic |
Author |
Message |
BigAl P4

Joined: 06 May 2003 Posts: 2995 Location: U.K Surrey
|
Posted: Sun Jan 03, 2010 10:32 am Post subject: Mayonnaise in the oil filler neck |
|
|
When I removed my oil filler neck to do my clutch slave cylinder I noticed that it had the usual mayo in it. I cleaned all this out when I first got my car and was surprised to see it again in such a short period of time.
Is there any way to prevent this?
Can the moisture be let out by removing the oil filler cap after the car has been driven for a while, whilst the engine and oil is hot and the cap be put back before it cools and allows moisture to settle in.
I noticed the mayo in the oil breather pipe to the plenum chamber pipe, does it get anywhere else that I can clean? _________________ x2 33 16v
pictures http://www.alfa-pages.co.uk/viewtopic.php?t=5203 |
|
Back to top |
|
 |
33bits 16 Valve
Joined: 23 May 2009 Posts: 1067 Location: Clevedon. North Somerset
|
Posted: Sun Jan 03, 2010 11:10 am Post subject: |
|
|
I think what you need to do Alan is buy a new car. . That will deff sort your probs out. _________________ 155 sportpack
33 16v Sportwagon
33 Permanent 4
33 16v (for sale)
156 JTS sportwagon
contact me for any 33 parts. Alex, 07896-327708
 |
|
Back to top |
|
 |
BigAl P4

Joined: 06 May 2003 Posts: 2995 Location: U.K Surrey
|
Posted: Sun Jan 03, 2010 12:48 pm Post subject: |
|
|
I hate it when people say "buy a new car" what’s the point as I could end up doing exactly what I have done "maintenance wise" to my car, all over again, better the devil you know.
Mayonnaise in the oil filler cap is normal, so I have heard on the boxers. I would like to minimise it if possible.
My car gets 2 45 mile journeys once a week, is that long enough to get rid of condensation? _________________ x2 33 16v
pictures http://www.alfa-pages.co.uk/viewtopic.php?t=5203 |
|
Back to top |
|
 |
Oggie Green Cloverleaf

Joined: 06 Mar 2008 Posts: 811 Location: Whitehill
|
Posted: Sun Jan 03, 2010 2:08 pm Post subject: |
|
|
You can drill a hole in the top of the cap and run a 22mm coolant/braided hose to an alloy catch tank (about £40) it has a small 2-3mm hole in the top so it keep oil pressure in the block. You have to empty the tank every 3-4 months of water but it stops the mayo dropping back into your motor. It should only take about an hour to fix Al. _________________ PHAT 33 |
|
Back to top |
|
 |
BigAl P4

Joined: 06 May 2003 Posts: 2995 Location: U.K Surrey
|
Posted: Sun Jan 03, 2010 4:40 pm Post subject: |
|
|
Thanks Iain,
Thats good to know, when i get some spare money, after paying you, i might look into it.
It wasn't as bad as i thought, easily cleaned the filler neck. _________________ x2 33 16v
pictures http://www.alfa-pages.co.uk/viewtopic.php?t=5203 |
|
Back to top |
|
 |
33bits 16 Valve
Joined: 23 May 2009 Posts: 1067 Location: Clevedon. North Somerset
|
Posted: Sun Jan 03, 2010 9:57 pm Post subject: |
|
|
Hi Alan, was only pulling your leg about getting a new car bud, i've just posted you some bits for it, you should get them tues.  _________________ 155 sportpack
33 16v Sportwagon
33 Permanent 4
33 16v (for sale)
156 JTS sportwagon
contact me for any 33 parts. Alex, 07896-327708
 |
|
Back to top |
|
 |
BigAl P4

Joined: 06 May 2003 Posts: 2995 Location: U.K Surrey
|
Posted: Mon Jan 04, 2010 8:26 am Post subject: |
|
|
Thanks Alex, I know, or at least hopped you were kidding, otherwise you would have offered to sell me one of yours  _________________ x2 33 16v
pictures http://www.alfa-pages.co.uk/viewtopic.php?t=5203 |
|
Back to top |
|
 |
BigAl P4

Joined: 06 May 2003 Posts: 2995 Location: U.K Surrey
|
Posted: Mon Jan 04, 2010 10:11 am Post subject: |
|
|
Oggie wrote: |
You can drill a hole in the top of the cap and run a 22mm coolant/braided hose to an alloy catch tank (about £40) it has a small 2-3mm hole in the top so it keep oil pressure in the block. You have to empty the tank every 3-4 months of water but it stops the mayo dropping back into your motor. It should only take about an hour to fix Al. |
I saw one where you remove the oil breather pipe and then connect one pipe to the oil filler neck and the other pipe to the inlet plenum, basically replacing the original pipe, they look very nice.
I didn't realise their purpose was to catch moisture as well _________________ x2 33 16v
pictures http://www.alfa-pages.co.uk/viewtopic.php?t=5203 |
|
Back to top |
|
 |
|